Custom Floor
Shopping Cart
0 items
We Install We Install

10 Buckets of Stauf SMP-940 Superior Wood Floor Adhesive 3 Gallon

10 Buckets of Stauf SMP-940 Superior Wood Floor Adhesive 3 Gallon
Click to enlarge
Price: $1,219.00
Availability: In Stock
Model: a-st001bu10
Manufacturer: Stauf
Average Rating: Not Rated

10 Buckets of Stauf SMP-940 Superior Wood Floor Adhesive 3 Gallon

3 Gallon Size

This listing is for ten (10) units.

Special features

  • 3 Gallon
  • Certified "Green" under highest standards
  • easy clean up; easy to spread
  • no isocyanates to etch finished floors
  • twice the shear strength of competitors
  • moisture cured for a strong bond

Product Description

STAUF SMP-940 Superior is an advanced formula polymer designed for professional wood flooring installation. It replaces isocyanate-containing urethane adhesives. It is ozone and environmentally safe since there are no solvents or other hazardous materials contained in it. This adhesive has earned the highest GEV-EMICODE EC 1 ranking by the European Association for Control of Emissions for Flooring. See for information. Because there is no water or solvent present, it will not cause dimensional changes to wood flooring. This adhesive is waterproof when fully cured and will not dissolve if it gets wet. However, it will not prevent moisture-related damages to wood flooring.

The adhesive spreads easily and has a non-slump formula that will help insure contact and adhesive transfer because the ridges will bridge normal gaps between the flooring and sub floor. It allows fast installation even with complicated patterns due to its strong green grab. There is no flash time required, so installation can commence immediately. Rolling is neither required nor recommended. It offers superior flexibility and is designed to keep the flooring in place, yet allow for normal movement during seasonal changes to the flooring.

Pre-Installation Checklist

A successful installation requires proper preparation of the sub floor. Read and understand all applicable guidelines and technical data sheets before beginning installation. Follow industry standards and flooring manufacturer's recommendations for sub floor moisture content, design, layout and application of flooring materials. All slab constructions must meet the specific requirements of the floor covering to be installed.

Sub Floor Examination

Prior to starting, the sub floor must be checked according to NWFA installation guidelines. It must be solid and sound, flat, permanently dry, clean, free of chaps, indentations and anti-adherents, as well as resistant to pressure and tension. Moisture content of all floors must be measured before installation.

Moisture content in concrete sub floors must be below 3#/24h/1,000 sq. ft. using the Calcium Chloride Test. All wood floors should have 6-9% moisture content at installation. There should be no more than a 4-5% variance in moisture content between the wood flooring and any wood sub floor. See NWFA guidelines and the wood flooring manufacturer's recommendations for details.

Sub Floor Preparation

Depending on type and condition of sub floor, a mechanical treatment (e.g. mechanical brushing, grinding or sanding) is required. Intensity of such work must be determined at the site by the installer. Dust, paint, residual adhesives or other surface pollution must be removed by suitable means. We recommend cleaning the surface with an industrial vacuum cleaner. Cracks and gaps must be filled with concrete crack filler CCF-30, unless they are expansion joints. Level when necessary to 3/16 inches within 10 feet. Heated sub floors must be primed.

Installation Procedure

Spread the adhesive with the appropriate notched trowel. Avoid excessive adhesive thickness by passing the trowel evenly through the adhesive at a 45 degree angle. There is no flash time, so installation should begin immediately. Lay the flooring into the adhesive, correctly position it and press down firmly. Rolling is neither required nor recommended. Be sure to check the boards at regular intervals to make certain good adhesive transfer from floor to flooring is accomplished.


When using other than Stauf products in combination with Stauf sealers, we deny any and all responsibility for any ensuing problems and/or damages without prior written permission from Stauf.

Do not install solid wood below grade. Do not use on concrete with curing agents or sealers except approved Sealers listed below. Do not use on damp sub floors. Do not install wood flooring with a moisture reading above 9%. Do not use adhesive as a leveling material.

This adhesive is waterproof when fully cured and will not dissolve if it gets wet. However, it will not prevent moisture-related damages to wood flooring.

In case of accident, injury, spill or exposure, see MSDS sheet for information. Consult technical data sheet at for updated information.


General Features
  • contains no isocyanates to etch floors's finish
  • twice the shear strength of competitors
  • contains no solvents
  • contains no VOC
  • certified "green"
  • certified "very low emission"
  • nonflammable
  • high solids content
  • ozone friendly
  • special polymer will not etch floor's finish
  • moisture cured for a strong bond
  • Freeze/thaw stable
Installation Features
  • wet lay - no flash time required
  • strong green grab
  • non-slump formula
  • bridges normal sub floor variations
  • very low odor
  • cleans with acetone or mineral spirits
  • no rolling required
  • does not cause cupping of wood flooring
  • excellent spread rate
  • long open time
  • spreads easily
  • higher temp & RH will shorten drying time
Long Term Features
  • resistant against aging
  • remains elastic
  • suitable for radiant heat systems with primer
  • allows normal dimensional changes in wood flooring
  • adhesive is waterproof when cured
Approved Flooring
  • Engineered Flooring, 1/4"-3/4", any width
  • Strip Flooring, Solid, 5/16"-3/4", up to 3" wide
  • Solid Shorts, 1/2" - 3/4", any width
  • Solid Planks, 1/2" - 3/4", any width
  • Parquet, Engineered, 5/16"
  • Parquet, Solid, 5/16"
  • Bamboo Flooring (except Stranded Bamboo)
  • Solid Wood Flooring must be straight and flat.
Approved Sub Floors
  • Concrete Slabs
  • OSB (underlayment grade)
  • Plywood (underlayment grade)
  • Particle or Chipboard (underlayment grade)
  • Old Floors with adhesive residues, sanded
  • Ceramic Tiles
  • Stone, Terrazzo
  • Cured Leveling Compounds
  • Radiant Heated Sub Floors


Approved Primers
  • Primer is normally not required
  • STAUF AQP-200 Eco-Prime
Approved Sealers
  • STAUF ACS-210 True-Seal
  • STAUF ERP-270 Epoxy-Prime
Approved Leveling Compounds
  • STAUF FLC-500 Leveling Compound
  • STAUF QFP-520 Quick Floor Patch
Approved Underlayments
  • STAUF SCU-600 Sound Comfort Underlay
  • STAUF SCU-610 Sound Control Underlay
Approved Trowels and Spread Rate
  • Trowel #14 (Solid&Engineered Floors): up to 85 SF/gal.
  • Trowel #5 (Engineered Floors): up to 60 SF/gal.
  • Trowel #4 (Solid Floors): up to 50 SF/gal.
  • Trowel #3 (Parquet Wood Floors): up to 70 SF/gal.
  • Trowel #15 (Underlayments): up to 100 SF/gal.
Cure Time until Normal Traffic
  • between 24 and 48 hours
  • Use acetone or mineral spirits while wet or dried
Temperature Range during Installation
  • 50°-90°F
Relative Humidity Range during Installation
  • 30% - 80%
Packaging Size
  • 3 gal. Plastic Pail
  • 3/4 gal. Plastic Pail
Weight [lbs./gal.]
  • 14
Write Review
Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad            Good

Enter the code in the box below:

There are no additional images for this product.